| |
| Surname |
|
S-ID |
00000 |
| Specification |
|
WPS-no. |
|
| Test |
|
Date of welding |
|
|
|
| |
| |
| WPS related |
Quality levels |
| |
B |
C |
D |
| t₁ |
= |
mm |
z₁ |
= |
mm |
|
|
|
|
| t₂ |
= |
mm |
z₂ |
= |
mm |
|
|
|
|
| D₁ |
= |
mm |
a₁ |
= |
mm |
|
a₁ ≥ 0.0 mm |
|
a₁ ≥ 0.0 mm |
|
a₁ ≥ 0.0 mm |
|
| b |
= |
mm |
b |
= |
|
|
|
|
|
|
|
|
| c |
= |
mm |
h₁ |
= |
mm |
|
h₁ = 0.0 - 1.5 mm |
|
h₁ = 0.0 - 1.5 mm |
|
h₁ = 0.0 - 1.5 mm |
|
| α |
= |
° |
|
|
|
|
|
|
|
|
|
|
| β |
= |
° |
|
|
|
|
|
|
|
|
|
|
| R |
= |
° |
|
|
|
|
|
|
|
|
|
|
| Visual inspection: ISO 17637 / Assessment norm |
| |
503 = max. weld reinforcement |
5213 = max. Corner weld thickness |
Mistake code |
Assessment |
| |
Measuring point 1 |
Measuring point 2 |
|
actual
value |
|
|
| Sample |
DL |
WL |
b₁ [mm] |
503 max |
h₁ [mm] |
b₂ [mm] |
503 max |
h₂ [mm] |
a |
5213 max |
a₁ |
a₂ |
507 |
512 |
5011 |
5012 |
|
|
accepted / not accepted |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Radiographic testing: ISO 1763ff / Assessment norm ISO 10675-1 |
| |
Densitometry |
Reference No. ISO6520 |
Assessment |
| Sample |
ISO 6520-1 |
BPK-F |
2011 |
2012 |
2016 |
303 |
401 |
402 |
5011 |
|
|
accepted / not accepted |
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| Fracture test: ISO 9070 / Assessment norm |
| |
Reference No. / Reference: ISO 6520 |
Assessment |
| Sample |
DL |
WL |
position of fracture |
2011 |
2012 |
2016 |
303 |
401 |
402 |
|
|
|
accepted / not accepted |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ¹) Test piece = not accepted |
| The measurements at the Visual inspection to a (thickness of the fillet weld) and b (width of weld convexity) must be entered including the border and actual values. Ascertained irregularities shall be documented in the evaluation sheet with 'X'. If the limit value is exceeded for a specified admissibility range, the actual value must be documented instead. |
| |
| |
Ja |
|
Nein |
|
The identity of the test participant was verified and established using a valid, official photo document. |
|
| |
Ja |
|
Nein |
|
The suitability of the test participant was checked and determined. |
|
| |
Ja |
|
Nein |
|
The suitability of the examination location and theory examination was checked and determined before the start of the examination. |
|
| |
Ja |
|
Nein |
|
The procedure for the technical knowledge examination was discussed with the test candidate before the start of the examination. |
|
| |
Job knowledge (): |
|
accepted |
|
not accepted |
Type of test: |
| |
| Overall assessment: |
|
accepted |
|
not accepted |
| |
|
| Date |
|
Stamp, Name and signature of examiner or of examining body |
|
Supervising (Date, Surname, Signature) |
| |